uPVC Window Repair
While uPVC windows are hardy and resistant to extreme weather conditions, they can still develop issues that need fixing. Luckily these problems can be fixed at a less than the cost of replacing windows.
A common problem is that a window becomes difficult to open because the hinges are stiff. This can be easily resolved by lubricating hinges with WD-40.
Broken or cracked glass
Glass is everywhere in our homes: on doors, windows and tables as well as in microwaves and stoves, even in frames for pictures. A good baseball hit or a rough-housing session with friends can cause cracks in your windows that need to be repaired promptly before they get any worse. These types of cracks can be easily repaired without the need to replace the window glass or frame.
First, clean the area with a damp cloth to remove any dirt, dust or fingerprints. Use a small amount epoxy to seal the crack. Let the epoxy dry completely before moving the window back. This is a simple repair that will save you the expense of replacing your uPVC windows.
Another common problem with uPVC windows is that the gasket on the window becoming weak or falling off from the frame. This will result in a loss of insulation as well as a let in of cold air or water into your home. This can be easily fixed with a flat blade such as the bank card to break the gasket from the frame of the window. If you have the time, you could add a bit more epoxy to the crack so that it appears as if it has never existed.
Apply RepairMyWindowsAndDoors of tape to fix the crack if it is too deep to reach with your fingers. This will prevent further damage. You could also use clear nail polish as a filler to stop the crack from spreading. It is important to start this process as soon as you detect the crack, or it will spread quickly and be more difficult to repair.
If you are looking for a more permanent fix, consider uPVC epoxy. It is the most labor-intensive of the options, but it will provide the most efficient results in terms strength and appearance. Follow the manufacturer's directions for applying the epoxy. Once it is dry, use a rag soaked in acetone to polish the surface.
Water Leaks
uPVC windows are durable however, they need some attention and maintenance. They can cause a myriad of problems if they are not maintained properly. The causes can range from leaking water around the frame to condensation inside the glass units.
A skilled uPVC window repair expert can help identify the issue and then fix it. They can also give suggestions on how to avoid it occurring again in future.
Leaking uPVC Windows can be a major problem and should be addressed as soon as they begin to occur. If ignored, the damage can cause major damp issues to your home, leading to costly repairs and a decrease in energy efficiency.
In many cases, a leaking uPVC window can be repaired by a simple leak patch. This is a sealant which is applied to the inside of the window. This will prevent water from getting into your home through the damaged region.
Double-glazed units that are misty or cloudy may be an indication of a failed seal. This could be caused by a variety of factors, including wear and tear, age weather conditions, or simply age.
You can prevent this from happening by having your windows regularly cleaned. It is recommended that you clean your windows at a minimum of twice each year using white soft cloth that has been immersed in warm soapy water. Avoid using colored cloths, as they can leave dye stains. For stubborn stains, it is best to apply solvent PVC cleaner. This is available from any hardware store and is easy to apply. Remember to wipe the window frames in a shaded area away from direct sunlight to avoid any streaking.
The Locks and hinges are faulty and faulty.
Over time, a window hinge can be bent or damaged. This can result in an opening in the frame, which can let in draughts and decrease the efficiency of energy. A draft can also make your home cold and uncomfortable, and increase your heating costs.
A gap in a uPVC is an issue which can be easily corrected. A uPVC window repair expert will be able to pinpoint the problem and fix it for you. A small hole can usually be repaired with carpenter’s glue and a wooden stick inserted into the gap. The dowel must be positioned so that it is in line with the hinge leaf, and has a smooth finish. The adhesive of a carpenter is spread on the dowel, and then tapped into position. Once it has dried and cured, a screw is installed to fix the hinge.
UPVC window hinges or locks can become stiff over time due to wear and tear, or due to blockages caused by dirt or debris. They should be cleaned and checked often to ensure they are working correctly. A lubricant such as WD-40 should be used to keep the moving components in good condition.
It is recommended to wash UPVC windows at least two times per year. This should be done using a damp cloth that has been dipped in a mixture of mild soap and water. The areas around the corners of the window should be cleaned more frequently in order to avoid build up of dirt and corrosion.
It may also be difficult to open or shut the handle of uPVC windows. This can be a result of the handle being dropped or caused by problems with the locking system. This is a simple and quick repair that can be completed by the homeowner if they follow some simple steps.
A damaged lock could be an actual security risk since it could mean that your home isn't secured and could potentially be vulnerable to burglars. A damaged lock could cause your uPVC window or door difficult to open which can be an inconvenience for you. A new handle or a re-alignment of the multipoint locking mechanism may be required if this is the case.
Stuck Handle
It can be quite a hassle when your upvc window handle becomes stuck, especially when you try to open the window and it requires an enormous amount of force or doesn't open at all. This is usually caused by a wire that sits inside the handle holder, and has become rough. By simply undoing the handle and taking a look at the wire, you are able to smooth out the rough spot and solve your problem.
Another method to get this fixed is by using a graphite or paraffin lubricant on the pole sliders which allows the handle to move upwards and downwards. It's also a good time to give your handle a general clean to keep any issues from occurring related to it.
If the issue is with the push button, it can be fixed by applying superglue. Make sure the superglue is dry prior to trying to use it again. If the handle is completely damaged or broken it can be repaired by ordering a replacement and then screwing it into place. This is a far simpler repair than replacing the entire window frame and is something you can tackle yourself, especially if you have the right tools.